https://thedxt.ca/2023/06/moving-windows-recovery-partition-correctly/

• Make sure you have a backup of the system you are going to edit the partitions on.
• Open Command Prompt as admin

Run CMD as admin

• We need to disable the existing Windows Recovery Partition to do that run the command reagentc /disable

Disabling the Recovery Partition

The reagentc /disable command will disable the recovery partition and will move the recovery partition into a file named Winre.wim and will be located in C:\Windows\System32\Recovery (you have to enable showing hidden system files if you want to see it)

The Windows Recovery Partition File

• Run the command diskpart to launch DiskPart

Launching DiskPart

• List the disks in your system. You can do this by using the command list disk

Listing the disks in DiskPart and showing the disk is a GPT disk

Pro tip from Matt in the comments, if there’s a * in the column for Gpt that means the disk is likely a GPT disk and if there isn’t a * in the Gpt column the disk is likely MBR. Make a note of this as it will be important further down.

• Select the disk you need to move the recovery partition on. You can do this by using the command select disk and the disk number. In my setup disk 0 was the correct disk and the command I entered was select disk 0.

Selecting the disk in DiskPart

• List the partitions on that disk. You can do this by using the command list partition

Listing the partitions in DiskPart

• Select the recovery partition. You can do this by using the command select partition and the partition number. In my setup partition 4 is my recovery partition and the command I entered was select partition 4

Selecting the partition in DiskPart

The recovery partition is a protected partition so we need to use a bit more force to delete it.

• Force the deletion of the recovery partition. You can do this by using the command delete partition override

Forcing the partition deletion

Now if you look in Disk Management you should no longer have the Recovery Partition and it should show up as unallocated.

Disk Management with the Recovery Partition deleted

• Expand your disk and leave about 1024 MB off your resized size to leave room for the re-enabling the Recovery Partition.

Expanding the partition but leaving room for the Windows Recovery Partition

Disk Management should now look something like this.

Disk Management after expanding the disk and leaving room for the Windows Recovery Partition

Once the disk is expanded we need to rebuild everything that is needed for Windows to know that the extra space that we left unallocated can be used to for the recovery partition.

• Create a New Simple Volume with the unallocated space.

Creating a New Simple Volume

• Don’t give it a drive letter.

Not giving the New Simple Volume a drive letter or a drive path

• You can give the new partition a name if you want it does not mater. I’m going to call mine New Recovery.

Naming the New Simple Volume

Disk Management should now look something like this.

Disk Management with the newly created partition that will become the Windows Recovery Partition

• In DiskPart list your partitions again by running the command list partition

Listing the partitions with DiskPart

• Select the 1024 MB partition with the command select partition and the partition number. In my setup it was partition 4 and the command I ran was select partition 4

Selecting the partition with DiskPart

If you have a GPT disk you need to run some very specific command and if you have an MBR disk you need to run different very specific commands.

On GPT disks we need to change the partition ID to de94bba4-06d1-4d40-a16a-bfd50179d6ac which tells Windows that this is a recovery partition

• Run the following command to set the partition as a recovery partition set id=de94bba4-06d1-4d40-a16a-bfd50179d6ac

Setting the GPT partition ID in DiskPart

We also need to hide the drive and flag it as a required partition to do that we have to set a GPT attribute to 0x8000000000000001

• Run the following command to set the GPT attribute to hide the drive and flag it as required gpt attributes=0x8000000000000001

Setting the GPT attribute in DiskPart

• Now we can exist DiskPart.

Exiting DiskPart

On MBR disks we need to change partition ID to 27 which will tell Windows that this is a recovery partition.

• Run the following command to set the partition as a recovery partition set id=27

setting the MBR partition ID in DiskPart

• Now we can exist DiskPart.

Exiting DiskPart

• Now we can re-enable the recovery partition by running the command reagentc /enable

Enabling the Windows Recovery Partition

The reagentc /enable command will copy the Winre.wim file from C:\Windows\System32\Recovery into our new recovery partition.

Windows Recovery Partition file is now back on the recovery partition

If you look at Disk Management again everything shows up correctly.

That’s all there is to it.

Technically speaking we did just delete the Windows Recovery Partition but we did so in a way to keep our existing recovery partition safely intact and then we rebuild the recovery partition and re-enabled it.

I prefer doing it this way as it leaves your recovery options intact and you can do it all live without any reboots.